smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: MAXTOR 6L080J4 Serial Number: 664212401373 Firmware Version: A93.0500 Device is: In smartctl database [for details use: -P show] ATA Version is: 5 ATA Standard is: ATA/ATAPI-5 T13 1321D revision 1 Local Time is: Sat Sep 25 06:19:44 2004 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled The SMART RETURN STATUS return value (smartmontools -H option/Directive) can not be retrieved with this version of ATAng, please do not rely on this value === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 35) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 40) minutes. SMART Attributes Data Structure revision number: 11 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x0029 100 253 020 Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 075 065 020 Pre-fail Always - 3184 4 Start_Stop_Count 0x0032 100 100 008 Old_age Always - 158 5 Reallocated_Sector_Ct 0x0033 100 100 020 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 093 023 Pre-fail Always - 0 9 Power_On_Hours 0x0012 085 085 001 Old_age Always - 10411 10 Spin_Retry_Count 0x0026 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 008 Old_age Always - 145 13 Read_Soft_Error_Rate 0x000b 100 093 023 Pre-fail Always - 0 194 Temperature_Celsius 0x0022 082 077 042 Old_age Always - 48 195 Hardware_ECC_Recovered 0x001a 100 002 000 Old_age Always - 5110106 196 Reallocated_Event_Count 0x0010 100 253 020 Old_age Offline - 0 197 Current_Pending_Sector 0x0032 100 100 020 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x001a 197 197 000 Old_age Always - 3 SMART Error Log Version: 1 ATA Error Count: 1 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 occurred at disk power-on lifetime: 4735 hours (197 days + 7 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 d1 20 b7 9a 55 e2 Error: UNC at LBA = 0x02559ab7 = 39164599 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c4 02 80 57 9a 55 e2 55 00:04:13.314 READ MULTIPLE ca 04 08 df b9 c0 e4 c0 00:04:13.314 WRITE DMA ca 04 08 4f bd bd e4 bd 00:04:13.313 WRITE DMA ef 02 46 01 00 00 a0 55 00:04:13.311 SET FEATURES [Enable write cache] ef 00 0c 01 00 00 a0 5f 00:04:13.311 SET FEATURES [Reserved subcommand] SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Device does not support Selective Self Tests/Logging