BUFFALO U-BOOT Ver 1.00 == CPU:680MHz, DDR:340MHz, AHB:170MHz == AP96 (ar7100) U-boot 0.0.1 DRAM: 128 MB Top of RAM usable for U-Boot at: 84000000 Reserving 265k for U-Boot at: 83fbc000 Reserving 192k for malloc() at: 83f8c000 Reserving 44 Bytes for Board Info at: 83f8bfd4 Reserving 36 Bytes for Global Data at: 83f8bfb0 Reserving 128k for boot params() at: 83f6bfb0 Stack Pointer at: 83f6bf98 Now running in RAM - U-Boot at: 83fbc000 flash bank #0 found 16 MB flash [W25Q128BV, blk:0x10000, sectors:256] flash bank #1 found 16 MB flash [W25Q128BV, blk:0x10000, sectors:256] Flash: 32 MB In: serial Out: serial Err: serial Memory Test uboot use 83F6BFB0 - 84000000 Memory Test start(80000000) end(83F00000) size(03F00000) Pattern 00000000 Writing... Reading... Memory Test start(84000000) end(88000000) size(04000000) Pattern 00000000 Writing... Reading... Memory Test OK ### buf_ver=[1.00] U-Boot Ver.=[1.00] ### build_date(env)=[Jun 1 2010 - 13:48:44] build_date(bin)=[Jun 1 2010 - 13:48:44] ag7100_enet_initialize... Reading MAC Address from ENV(0x83f8c2fd) Port 0, Neg Success Port 1, Neg Success Port 2, Neg Success Port 3, Neg Success eth0: Phy Specific Status=0010 eth0: Phy Specific Status=0010 eth0: Phy Specific Status=0010 eth0: Phy Specific Status=00102leth0: 02:aa:bb:cc:dd:20 eth0 up Reading MAC Address from ENV(0x83f8c2fd) Port 4, Neg Success eth1: Phy Specific Status=0010 eth1: 02:aa:bb:cc:dd:21 eth1 up eth0 02:AA:BB:CC:DD:20 , eth1 02:AA:BB:CC:DD:21 enet0 port0 up pll reg 0x18050010: 0x110000 tftp server(receive) go, waiting:4[sec] Load address: 0x84000000 TftpServer Timeout; no file was loaded. change bootargs console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ar7100-nor0:256k(u-boot),64k(u-boot-env),1152k@384k(uImage),6592k@1536k(rootfs),64k@320k(ART),64k@8128k(properties),8192k@8192k(flash1),16384k@16384k(flash2) mem=128M ## Booting image at bf060000 ... Image Name: FreeBSD Created: 2014-09-13 21:26:27 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1601635 Bytes = 1.5 MB Load Address: 80050000 Entry Point: 80050100 Verifying Checksum ... crc32_fw: bf060040 - bf1e70a2 (len:00187063) calc... crc32_fw: range1 bf060040 - bf1e70a2 OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80050100) ... ## Giving linux memsize in bytes, 134217728 Starting kernel ... CPU platform: Atheros AR7161 rev 2 CPU Frequency=680 MHz CPU DDR Frequency=340 MHz CPU AHB Frequency=170 MHz platform frequency: 680 MHz CPU reference clock: 40 MHz CPU MDIO clock: 40 MHz arguments: a0 = 00000007 a1 = a3f6bfb0 a2 = a3f6c4b0 a3 = 00000020 Cmd line:argv is invalid Environment: envp is invalid Cache info: picache_stride = 4096 picache_loopcount = 16 pdcache_stride = 4096 pdcache_loopcount = 8 cpu0: MIPS Technologies processor v116.147 MMU: Standard TLB, 16 entries L1 i-cache: 4 ways of 512 sets, 32 bytes per line L1 d-cache: 4 ways of 256 sets, 32 bytes per line Config1=0x9ee3519e Config3=0x20 Physical memory chunk(s): 0x864000 - 0x7ffffff, 125419520 bytes (30620 pages) Maxmem is 0x8000000 KDB: debugger backends: ddb KDB: current backend: ddb Copyright (c) 1992-2014 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 11.0-CURRENT #1 r271466M: Sat Sep 13 14:25:29 PDT 2014 sbruno@alice:/home/sbruno/bsd/obj/mips/mips.mips/home/sbruno/bsd/fbsd_head/sys/WZR-HPAG300H mips gcc version 4.2.1 20070831 patched [FreeBSD] WARNING: WITNESS option enabled, expect reduced performance. MEMGUARD DEBUGGING ALLOCATOR INITIALIZED: MEMGUARD map base: 0xc0800000 MEMGUARD map size: 104860 KBytes Preloaded elf kernel "kernel" at 0x8085d870. real memory = 134217728 (131072K bytes) Physical memory chunk(s): 0x008f8000 - 0x07da6fff, 122351616 bytes (29871 pages) avail memory = 121376768 (115MB) random device not loaded; using insecure entropy wlan: <802.11 Link Layer> mem: null: nexus0: clock0: on nexus0 Timecounter "MIPS32" frequency 340000000 Hz quality 800 Event timer "MIPS32" frequency 340000000 Hz quality 800 argemdio0: at mem 0x1a000000-0x1a000fff on nexus0 mdio0: on argemdio0 mdioproxy0: on mdio0 apb0 at irq 4 on nexus0 uart0: <16550 or compatible> at mem 0x18020003-0x1802001a irq 3 on apb0 uart0: console (115200,n,8,1) uart0: fast interrupt gpio0: at mem 0x18040000-0x18040fff irq 2 on apb0 gpio0: [GIANT-LOCKED] gpio0: function_set: 0x3004 gpio0: function_clear: 0x0 gpio0: gpio pinmask=0x1 gpioc0: on gpio0 gpiobus0: on gpio0 gpioiic0: invalid pin 13, max: 11 gpioled0: at pin(s) 0 on gpiobus0 ehci0: at mem 0x1b000000-0x1bffffff irq 1 on nexus0 usbus0: set host controller mode usbus0: EHCI version 1.0 usbus0: set host controller mode usbus0 on ehci0 ehci0: usbpf: Attached pcib0 at irq 0 on nexus0 pcib0: ar71xx_pci_attach: missing hint 'baseslot', default to AR71XX_PCI_BASE_SLOT pcib0: ar71xx_pci_slot_fixup: checking dev pcib0, 0/17/0 pcib0: found EEPROM at 0x1f051000 on 0.17.0 pcib0: ar71xx_pci_fixup: flash_addr=1f051000, cal_data=0xbf051000 reg: 6000, val=29168c reg: 6008, val=2800001 reg: 602c, val=a097168c reg: 5000, val=2a168c reg: 5008, val=2800001 reg: 502c, val=a097168c reg: 5064, val=5040cc0 reg: 506c, val=33811 reg: 4004, val=40073b reg: 4074, val=3 reg: 4000, val=1c20000 reg: 6034, val=44 pcib0: EEPROM firmware: 0x1f051000 @ 4096 bytes firmware: 'pcib.0.bus.0.17.0.eeprom_firmware' version 1: 4096 bytes loaded at 0xc6f12000 pcib0: device EEPROM 'pcib.0.bus.0.17.0.eeprom_firmware' registered pcib0: ar71xx_pci_slot_fixup: checking dev pcib0, 0/18/0 pcib0: found EEPROM at 0x1f055000 on 0.18.0 pcib0: ar71xx_pci_fixup: flash_addr=1f055000, cal_data=0xbf055000 reg: 6000, val=29168c reg: 6008, val=2800001 reg: 602c, val=a096168c reg: 5000, val=2a168c reg: 5008, val=2800001 reg: 502c, val=a096168c reg: 5064, val=5040cc0 reg: 506c, val=33811 reg: 4004, val=40073b reg: 4074, val=3 reg: 4000, val=1c20000 reg: 6034, val=44 pcib0: EEPROM firmware: 0x1f055000 @ 4096 bytes firmware: 'pcib.0.bus.0.18.0.eeprom_firmware' version 1: 4096 bytes loaded at 0xc6f15000 pcib0: device EEPROM 'pcib.0.bus.0.18.0.eeprom_firmware' registered pci0: on pcib0 pci0: domain=0, physical bus=0 found-> vendor=0x168c, dev=0x0029, revid=0x01 domain=0, bus=0, slot=17, func=0 class=02-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x02b0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=0 powerspec 2 supports D0 D3 current D0 map[10]: type Memory, range 32, base 0, size 16, memory disabled found-> vendor=0x168c, dev=0x0029, revid=0x01 domain=0, bus=0, slot=18, func=0 class=02-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x02b0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=0 powerspec 2 supports D0 D3 current D0 map[10]: type Memory, range 32, base 0, size 16, memory disabled ath0: irq 0 at device 17.0 on pci0 ath0: Lazy allocation of 0x10000 bytes rid 0x10 type 3 at 0x10000000 ath0: ath_pci_attach: looking up firmware @ 'pcib.0.bus.0.17.0.eeprom_firmware' ath0: ath_pci_attach: EEPROM firmware @ 0xc6f12000 ath0: [HT] enabling HT modes ath0: [HT] 1 stream STBC receive enabled ath0: [HT] 1 stream STBC transmit enabled ath0: [HT] 2 RX streams; 2 TX streams ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps ath0: 2T2R ath0: 11ng MCS 20MHz ath0: MCS 0-7: 6.5Mbps - 65Mbps ath0: MCS 8-15: 13Mbps - 130Mbps ath0: 11ng MCS 40MHz: ath0: MCS 0-7: 13.5Mbps - 135Mbps ath0: MCS 8-15: 27Mbps - 270Mbps ath0: 11ng MCS 40MHz SGI: ath0: MCS 0-7: 15Mbps - 150Mbps ath0: MCS 8-15: 30Mbps - 300Mbps ath0: AR9220 mac 128.2 RF5133 phy 13.0 ath0: 2GHz radio: 0x0000; 5GHz radio: 0x00c0 ath0: Use hw queue 1 for WME_AC_BE traffic ath0: Use hw queue 0 for WME_AC_BK traffic ath0: Use hw queue 2 for WME_AC_VI traffic ath0: Use hw queue 3 for WME_AC_VO traffic ath0: Use hw queue 8 for CAB traffic ath0: Use hw queue 9 for beacons ath0: using multicast key search ath1: irq 1 at device 18.0 on pci0 ath1: Lazy allocation of 0x10000 bytes rid 0x10 type 3 at 0x10010000 ath1: ath_pci_attach: looking up firmware @ 'pcib.0.bus.0.18.0.eeprom_firmware' ath1: ath_pci_attach: EEPROM firmware @ 0xc6f15000 [ath] enabling AN_TOP2_FIXUP ath1: [HT] enabling HT modes ath1: [HT] 1 stream STBC receive enabled ath1: [HT] 1 stream STBC transmit enabled ath1: [HT] 2 RX streams; 2 TX streams ath1: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps ath1: 2T2R ath1: 11na MCS 20MHz ath1: MCS 0-7: 6.5Mbps - 65Mbps ath1: MCS 8-15: 13Mbps - 130Mbps ath1: 11na MCS 40MHz: ath1: MCS 0-7: 13.5Mbps - 135Mbps ath1: MCS 8-15: 27Mbps - 270Mbps ath1: 11na MCS 40MHz SGI: ath1: MCS 0-7: 15Mbps - 150Mbps ath1: MCS 8-15: 30Mbps - 300Mbps ath1: AR9220 mac 128.2 RF5133 phy 13.0 ath1: 2GHz radio: 0x0000; 5GHz radio: 0x00c0 ath1: Use hw queue 1 for WME_AC_BE traffic ath1: Use hw queue 0 for WME_AC_BK traffic ath1: Use hw queue 2 for WME_AC_VI traffic ath1: Use hw queue 3 for WME_AC_VO traffic ath1: Use hw queue 8 for CAB traffic ath1: Use hw queue 9 for beacons ath1: using multicast key search arge0: at mem 0x19000000-0x19000fff irq 2 on nexus0 arge0: Overriding MAC from EEPROM arge0: arge_attach: overriding MII mode to 'RGMII' miiproxy0: on arge0 miiproxy0: attached to target mdio0 arge0: finishing attachment, phymask 0000, proxy set arge0: bpf attached arge0: Ethernet address: 4c:e6:76:50:84:ee arge1: at mem 0x1a000000-0x1a000fff irq 3 on nexus0 arge1: Overriding MAC from EEPROM arge1: arge_attach: overriding MII mode to 'RGMII' miiproxy1: on arge1 miiproxy1: attached to target mdio0 arge1: finishing attachment, phymask 0010, proxy set arge1: unable to attach PHY 4: 6 miiproxy1: detached device_attach: arge1 attach returned 6 spi0: at mem 0x1f000000-0x1f00000f on nexus0 spibus0: on spi0 mx25l0: at cs 0 on spibus0 mx25l0: w25q128, sector 65536 bytes, 256 sectors mx25l1: at cs 1 on spibus0 mx25l1: w25q128, sector 65536 bytes, 256 sectors ar71xx_wdog0: on nexus0 Device configuration finished. Timecounters tick every 1.000 msec tcp_init: net.inet.tcp.tcbhashsize auto tuned to 2048 lo0: bpf attached GEOM: new disk flash/spi0 GEOM: new disk flash/spi1 usbus0: 480Mbps High Speed USB v2.0 MAP: flash/spi0: 0x40000, data=0x40000 "/dev/map/uboot" MAP: flash/spi0: 40000x10000, data=0x10000 "/dev/map/u-boot-env" MAP: flash/spi0: 50000x10000, data=0x10000 "/dev/map/ART" MAP: search flash/spi0 for key ".!/bin/sh" from 0x160000, step 0x100000 ugen0.1: at usbus0 uhub0: on usbus0 MAP: flash/spi0: 60000x200000, data=0x200000 "/dev/map/kernel" MAP: search flash/spi0 for key ".!/bin/sh" from 0x160000, step 0x100000 MAP: flash/spi0: 260000xda0000, data=0xda0000 "/dev/map/rootfs" MAP: flash/spi1: ff0000x10000, data=0x10000 "/dev/map/cfg" map/rootfs.uncompress: GEOM_ULZMA image found map/rootfs.uncompress: 329 x 65536 blocks MAP: No valid partition found at map/rootfs.uncompress hwpmc: SOFT/16/64/0x67 MIPS24K/2/32/0x1ff WARNING: WITNESS option enabled, expect reduced performance. uhub0: 2 ports with 2 removable, self powered Trying to mount root from ufs:/dev/map/rootfs.uncompress []... warning: no time-of-day clock registered, system time will not be set accurately start_init: trying /sbin/init Sep 13 21:26:12 init: login_getclass: unknown class 'daemon' MAP: No valid partition found at md0 MAP: No valid partition found at md0 MAP: No valid partition found at md1 MAP: No valid partition found at md1 MAP: No valid partition found at md2 MAP: No valid partition found at md2 *** Populating /var .. *** Loading configuration files .. *** Restoring from /dev/map/cfg .. 1+0 records in 1+0 records out 65536 bytes transferred in 2.806777 secs (23349 bytes/sec) gunzip: invalid compressed data--crc error etc/cfg/manifest etc/master.passwd etc/group etc/cfg/rc.conf 7 blocks *** Completed. *** setting up hostname *** Load kernel modules Falling back to random adaptor random: initialized *** bringing up loopback .. *** Starting networking via /etc/rc.d/base/net dev.ath.0.txq_mcastq_maxdepth: 512 -> 32 dev.ath.1.txq_mcastq_maxdepth: 512 -> 32 *** Interface: arge0: start *** Interface: arge0: done *** Interface: bridge0: start bridge0: bpf attached bridge0: Ethernet address: e6:81:df:31:68:3b arge0: promiscuous mode enabled bridge0: link state changed to UP *** Interface: bridge0: done *** Default password/login databases .. *** inetd *** Done! FreeBSD/mips (freebsd-wifi-build) (ttyu0) login: