Building scterc-0.0.1.txz (origin /buildshare/ports/355755/sysutils/scterc) for powerpc-10-0 on XXX
slot2: created
x distfiles/
x distfiles/scterc-0.0.1.tar.gz
x packages/
x packages/smartmontools-6.2_2.txz
x packages/pkg-1.2.7_2.txz
x packages/gettext-0.18.3.1_1.txz
x packages/gmake-3.82_1.txz
ELF ldconfig path: /lib /usr/lib /usr/lib/compat
Make depends
===>   scterc-0.0.1 depends on file: /usr/local/sbin/pkg - not found
===>    Verifying install for /usr/local/sbin/pkg in /buildshare/ports/355755/ports-mgmt/pkg
===>   Installing existing package /packages/pkg-1.2.7_2.txz
Installing pkg-1.2.7_2... done
If you are upgrading from the old package format, first run:

  # pkg2ng
===>   Returning to build of scterc-0.0.1
===>   scterc-0.0.1 depends on file: /usr/local/sbin/smartctl - not found
===>    Verifying install for /usr/local/sbin/smartctl in /buildshare/ports/355755/sysutils/smartmontools
===>   Installing existing package /packages/smartmontools-6.2_2.txz
Installing smartmontools-6.2_2... done
smartmontools has been installed

To check the status of drives, use the following:

	/usr/local/sbin/smartctl -a /dev/ad0	for first ATA/SATA drive
	/usr/local/sbin/smartctl -a /dev/da0	for first SCSI drive
	/usr/local/sbin/smartctl -a /dev/ada0	for first SATA drive

To include drive health information in your daily status reports,
add a line like the following to /etc/periodic.conf:
	daily_status_smart_devices="/dev/ad0 /dev/da0"
substituting the appropriate device names for your SMART-capable disks.

To enable drive monitoring, you can use /usr/local/sbin/smartd.
A sample configuration file has been installed as 
/usr/local/etc/smartd.conf.sample
Copy this file to /usr/local/etc/smartd.conf and edit appropriately

To have smartd start at boot
	echo 'smartd_enable="YES"' >> /etc/rc.conf
===>   Returning to build of scterc-0.0.1
Make install
===>   scterc-0.0.1 depends on file: /usr/local/sbin/pkg - found
===> Fetching all distfiles required by scterc-0.0.1 for building
===>  Extracting for scterc-0.0.1
=> SHA256 Checksum OK for scterc-0.0.1.tar.gz.
===>  Patching for scterc-0.0.1
===>  Configuring for scterc-0.0.1
===>  Staging for scterc-0.0.1
===>   scterc-0.0.1 depends on file: /usr/local/sbin/smartctl - found
===>   Generating temporary packing list
install  -o root -g wheel -m 555 /obj/buildshare/ports/355755/sysutils/scterc/work/AMDmi3-scterc-rc.d-c8dc8c1/scterc.sh /obj/buildshare/ports/355755/sysutils/scterc/work/stage/usr/local/etc/rc.d/scterc
/bin/mkdir -p /obj/buildshare/ports/355755/sysutils/scterc/work/stage/usr/local/share/doc/scterc
install  -o root -g wheel -m 444 /obj/buildshare/ports/355755/sysutils/scterc/work/AMDmi3-scterc-rc.d-c8dc8c1/README.md /obj/buildshare/ports/355755/sysutils/scterc/work/stage/usr/local/share/doc/scterc/
====> Compressing man pages (compress-man)
===>  Installing for scterc-0.0.1
===>  Checking if sysutils/scterc already installed
===>   Registering installation for scterc-0.0.1
Installing scterc-0.0.1... done
To enable setting hard disk SCT ERC on system boot time, add the
following to your /etc/rc.conf:

  scterc_enable="YES"

  # specify hard disks to configure
  scterc_disks="ada0 ada1"

  # specify read and write timeouts in tenths of second
  # here each is set to 7.0 seconds, which is also the default
  # for which you may omit these lines
  scterc_read_timeout="70"
  scterc_write_timeout="70"

See /usr/local/share/doc/scterc/README.md for more info.

Make package
===>  Building package for scterc-0.0.1
slot2: removed