Building clockspeed-conf-0.4.5.txz (origin /buildshare/ports/355755/sysutils/clockspeed-conf) for powerpc-10-0 on XXX
slot2: created
x distfiles/
x distfiles/clockspeed-conf-0.4.5.tar.gz
x packages/
x packages/pkg-1.2.7_2.txz
x packages/libtai-0.60_4.txz
x packages/daemontools-0.76_16.txz
x packages/clockspeed-0.62_5.txz
ELF ldconfig path: /lib /usr/lib /usr/lib/compat
Make depends
===>   clockspeed-conf-0.4.5 depends on file: /usr/local/sbin/pkg - not found
===>    Verifying install for /usr/local/sbin/pkg in /buildshare/ports/355755/ports-mgmt/pkg
===>   Installing existing package /packages/pkg-1.2.7_2.txz
Installing pkg-1.2.7_2... done
If you are upgrading from the old package format, first run:

  # pkg2ng
===>   Returning to build of clockspeed-conf-0.4.5
===>   clockspeed-conf-0.4.5 depends on executable: supervise - not found
===>    Verifying install for supervise in /buildshare/ports/355755/sysutils/daemontools
===>   Installing existing package /packages/daemontools-0.76_16.txz
Installing daemontools-0.76_16... done
===>   Returning to build of clockspeed-conf-0.4.5
===>   clockspeed-conf-0.4.5 depends on executable: clockspeed - not found
===>    Verifying install for clockspeed in /buildshare/ports/355755/sysutils/clockspeed
===>   Installing existing package /packages/clockspeed-0.62_5.txz
Installing clockspeed-0.62_5...Installing libtai-0.60_4... done
mkdir: /usr/local/etc/clockspeed: File exists
pkg-static: POST-INSTALL script failed
 done
ATTENTIONATTENTION:

Please make sure that you read /usr/local/share/doc/clockspeed/INSTALL.
It contains important information about testing and configuring
clockspeed, and finally installing it in your system.

Clockspeed uses the libtai library, check /usr/ports/devel/libtai
for more details. TAI time measure is off 22 seconds from UTC time
measure. Therefore, your system time will show a 22 secs difference
from your time source after you've installed this port.

To fix this, you could follow this simple recipe created with
PR ports/27617.

1) killall clockspeed (you can't have it running)
2) sntpclock IP.OF.NTP.SERVER | clockadd
3) enable/start clockspeed :
	%25 cp /usr/local/etc/rc.d/clockspeed.sh.sample \
	  /usr/local/etc/rc.d/clockspeed.sh
	# enable clockspeed to automagically start next
	# time you reboot. do this after testing everything
	%25 /usr/local/etc/rc.d/clockspeed.sh start
	# start clockspeed now
4) sntpclock IP.OF.NTP.SERVER > /usr/local/etc/clockspeed/adjust
5) cd /usr/src/share/zoneinfo
6) make -DLEAPSECONDS clean all install ; make clean

Step 5 and 6 build support in your system for leapseconds handling.
Take a note about this since you might forget later to disable it
if you remove this port. To disable it, simply re-do step 6 without
-DLEAPSECONDS.
Step 6 should not break anything but you can disable it anytime
as per last paragraph if you think something unusual has happened
to your system.
 
7) /stand/sysinstall -> configure -> time zone (choose the correct
   time zone for your system)
8) sntpclock IP.OF.NTP.SERVER | clockview

Check how close is your clock before and after now. Should be
within milliseconds.

Do not forget to add a cron(8) job with step 4 to periodically
adjust clockspeed's drift rate. Once a week should be more than
adequate.

A port to non-i386 platforms was done using the clock_gettime(2)
function. Since this is somewhat experimental, there might be some
tiny precision differences from the i386 platform versions. You
have been warned!
===>   Returning to build of clockspeed-conf-0.4.5
Make install
===>   clockspeed-conf-0.4.5 depends on file: /usr/local/sbin/pkg - found
===> Fetching all distfiles required by clockspeed-conf-0.4.5 for building
===>  Extracting for clockspeed-conf-0.4.5
=> SHA256 Checksum OK for clockspeed-conf-0.4.5.tar.gz.
===>  Patching for clockspeed-conf-0.4.5
===>  Applying FreeBSD patches for clockspeed-conf-0.4.5
===>  Configuring for clockspeed-conf-0.4.5
===>  Building for clockspeed-conf-0.4.5
===>  Installing for clockspeed-conf-0.4.5
===>   clockspeed-conf-0.4.5 depends on executable: supervise - found
===>   clockspeed-conf-0.4.5 depends on executable: clockspeed - found
===>   Generating temporary packing list
===>  Checking if sysutils/clockspeed-conf already installed
mkdir -p /usr/local/bin/
install -m 755 clockspeed-conf /usr/local/bin/clockspeed-conf
install -m 755 taiclockd-conf /usr/local/bin/taiclockd-conf
mkdir -p /usr/local/man/man8/
install clockspeed-conf.8 /usr/local/man/man8/
install taiclockd-conf.8 /usr/local/man/man8/
cd /obj/buildshare/ports/355755/sysutils/clockspeed-conf/work/clockspeed-conf-0.4.5 && install  -o root -g wheel -m 444 COPYRIGHT README TODO /usr/local/share/doc/clockspeed-conf
***
*** Type 'make ids' to create user/group IDs
***
===>   Compressing manual pages for clockspeed-conf-0.4.5
===>   Registering installation for clockspeed-conf-0.4.5
Installing clockspeed-conf-0.4.5... done
Make package
===>  Building package for clockspeed-conf-0.4.5
Creating package for clockspeed-conf-0.4.5
slot2: removed