U-Boot 1.1.1  (Build time: Jun  8 2009 - 18:09:16)

CAPK-0100ND-CN50XX_1.8.1_294_v0.0.1

Hardware Monitor: W83792D initialized
CN3010_EVB_HS5 board revision major:0, minor:0, serial #: CAPK-0100ND
OCTEON CN5020-SCP pass 1.1, Core clock: 500 MHz, DDR clock: 265 MHz (530 Mhz data rate)
PAL rev: 0.00, MCU rev: 0.00, CPU voltage: 0.00
DRAM:  1024 MB
Flash:  8 MB
Clearing DRAM........ done
BIST check passed.
Starting PCI
PCI Status: PCI 32-bit
PCI BAR 0: 0x00000000, PCI BAR 1: Memory 0x00000000  PCI 0xf8000000
Net:   octeth0, octeth1, octeth2
 Bus 0 (CF Card): OK 

  ide 0: Model: CF Card Firm: Ver2.32 Ser#: 6EB1079B060700385875
            Type: Removable Hard Disk
            Capacity: 1923.9 MB = 1.8 GB (3940272 x 512)
Octeon capk_0100nd# run fbsd
Interface 0 has 3 ports (RGMII)
Using octeth0 device
TFTP from server 192.168.10.1; our IP address is 192.168.10.97
Filename 'kernel.CAPK_0100ND'.
Load address: 0xa800000
Loading: *octeth0: Down (port  0)
############################################################
done
Bytes transferred = 8483117 (81712d hex), 9921 Kbytes/sec
WARNING: Data loaded outside of the reserved load area, memory corruption may occur.
WARNING: Please refer to the bootloader memory map documentation for more information.
argv[2]: numcores=1
argv[3]: -s
ELF file is 64 bit
Attempting to allocate memory for ELF segment: addr: 0xffffffff80100080 (adjusted to: 0x0000000000100080), size 0x8fa940
Allocated memory for ELF segment: addr: 0xffffffff80100080, size 0x8fa940
Processing PHDR 0
  Loading 6c8f24 bytes at ffffffff80100080
  Clearing 231a1c bytes at ffffffff807c8fa4
## Loading Linux kernel with entry point: 0xffffffff80100080 ...
Bootloader: Done loading app on coremask: 0x1
Boot Descriptor Ver: 7 -> 1/2  CPU clock: 500MHz  Core Mask: 0
  Board Type: 11  Revision: 0/0
  Mac Address 00.90.FB.26.26.CA (3)
Model: CN5020p1.1-500-SCP
Cache info:
  picache_stride    = 4096
  picache_loopcount = 8
  pdcache_stride    = 256
  pdcache_loopcount = 64
cpu0: Cavium processor v1.6
  MMU: Standard TLB, 64 entries
  L1 i-cache: 4 ways of 64 sets, 128 bytes per line
  L1 d-cache: 64 ways of 2 sets, 128 bytes per line
  Config1=0xfe3303da<COP2,PerfCount,WatchRegs,EJTAG>
  Config3=0x1080
Physical memory chunk(s):
0x9fb000 - 0xfffafff, 257949696 bytes (62976 pages)
0x20000000 - 0x3fffffff, 536870912 bytes (131072 pages)
0x410000000 - 0x41fefffff, 267386880 bytes (65280 pages)
Maxmem is 0x41ff00000
pcpu is available at virtual address 0xc000000000000000.
GDB: debug ports: uart
GDB: current port: uart
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
Octeon SDK: Cavium Networks Octeon SDK version 2.0.0, build 366
Available Octeon features: SAAD CRYPTO USB
Copyright (c) 1992-2011 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.0-CURRENT #25: Wed Dec  7 19:52:25 PST 2011
    gonzo@cinderella.bluezbox.com:/src/FreeBSD/obj/git-octeon/mips.mips64eb/src/FreeBSD/git/sys/CN5020 mips
WARNING: WITNESS option enabled, expect reduced performance.
real memory  = 1062207488 (1037312K bytes)
Physical memory chunk(s):
0x00b18000 - 0x0fffafff, 256782336 bytes (62691 pages)
0x20000000 - 0x3e195fff, 504979456 bytes (123286 pages)
0x410000000 - 0x41fefffff, 267386880 bytes (65280 pages)
avail memory = 1021911040 (974MB)
ULE: setup cpu 0
mem: <memory>
nfslock: pseudo-device
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
nexus0: <MIPS32 root nexus>
WARNING:
cvmx_phys_to_ptr() passed a zero address
Compact flash found in bootbus region 1 (True IDE).
cf_wait_busy: device fault (status=ec)
cf_cmd_identify: identify failed: 5
clock0: <Generic MIPS32 ticker> on nexus0
Timecounter "MIPS32" frequency 500000000 Hz quality 800
Event timer "MIPS32" frequency 500000000 Hz quality 800
rnd0: <Cavium Octeon Random Number Generator> on nexus0
ciu0: <Cavium Octeon Central Interrupt Unit> on nexus0
obio0 on ciu0
uart1: <Octeon-16550 channel 1> on obio0
uart1: fast interrupt
uart1: debug port (115200,n,8,1)
uart0: <Octeon-16550 channel 0> on obio0
uart0: fast interrupt
uart0: console (115200,n,8,1)
octebus0: <Cavium Octeon Ethernet pseudo-bus> on ciu0
cavium-ethernet: Cavium Networks Octeon SDK version 2.0.0, build 366
Interface 0 has 3 ports (RGMII)
Warning: Enabling IPD when IPD already enabled.
Warning: Enabling PKO when PKO already enabled.
octe0: <Cavium Octeon RGMII Ethernet> on octebus0
miibus0: <MII bus> on octe0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 2 on miibus0
rgephy0: OUI 0x00e04c, model 0x0011, rev. 2
rgephy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
octe0: bpf attached
octe0: Ethernet address: 00:90:fb:26:26:ca
octe1: <Cavium Octeon RGMII Ethernet> on octebus0
miibus1: <MII bus> on octe1
rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 3 on miibus1
rgephy1: OUI 0x00e04c, model 0x0011, rev. 2
rgephy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
octe1: bpf attached
octe1: Ethernet address: 00:90:fb:26:26:cb
octe2: <Cavium Octeon RGMII Ethernet> on octebus0
octe2: bpf attached
octe2: Ethernet address: 00:90:fb:26:26:cc
pcib0: <Cavium Octeon PCI bridge> on ciu0
pcib0: 32-bit PCI bus.
pci0: <PCI bus> on pcib0
pci0: domain=0, physical bus=0
found->	vendor=0x1095, dev=0x3512, revid=0x01
	domain=0, bus=0, slot=12, func=0
	class=01-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x02b0, cachelnsz=16 (dwords)
	lattimer=0x30 (1440 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=0
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type I/O Port, range 32, base 0x4000, size  3, enabled
	map[14]: type I/O Port, range 32, base 0x4008, size  2, enabled
	map[18]: type I/O Port, range 32, base 0x4010, size  3, enabled
	map[1c]: type I/O Port, range 32, base 0x4018, size  2, enabled
	map[20]: type I/O Port, range 32, base 0x4020, size  4, enabled
	map[24]: type Memory, range 32, base 0xf0000000, size  9, enabled
found->	vendor=0x13a3, dev=0x0020, revid=0x00
	domain=0, bus=0, slot=14, func=0
	class=0b-40-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0280, cachelnsz=16 (dwords)
	lattimer=0x30 (1440 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=0
	map[10]: type Memory, range 32, base 0xf0001000, size 12, enabled
	map[14]: type Memory, range 32, base 0xf0002000, size 13, enabled
	map[18]: type Memory, range 32, base 0xf0008000, size 15, enabled
atapci0: <SiI 3512 SATA150 controller> port 0x4000-0x4007,0x4008-0x400b,0x4010-0x4017,0x4018-0x401b,0x4020-0x402f mem 0xf0000000-0xf00001ff irq 46 at device 12.0 on pci0
ata2: <ATA channel> at channel 0 on atapci0
ata3: <ATA channel> at channel 1 on atapci0
pci0: <processor> at device 14.0 (no driver attached)
octusb0: <Cavium Octeon USB controller> on ciu0
device_attach: octusb0 attach returned 6
rtc0: <Cavium Octeon Realtime Clock> on nexus0
rtc0: registered as a time-of-day clock (resolution 1000000us, adjustment 0.500000000s)
Device configuration finished.
procfs registered
Timecounter "Octeon" frequency 500000000 Hz quality 900
Timecounters tick every 10.000 msec
vlan: initialized, using hash tables with chaining
lo0: bpf attached
ata2: SATA connect timeout status=00000000
ata3: SATA connect timeout status=00000000
bootpc_init: wired to interface 'octe0'
octe0: link state changed to DOWN
Sending DHCP Discover packet from interface octe0 (00:90:fb:26:26:ca)
Received DHCP Offer packet on octe0 from 192.168.10.1 (accepted) (no root path)
Sending DHCP Request packet from interface octe0 (00:90:fb:26:26:ca)
Received DHCP Ack packet on octe0 from 192.168.10.1 (accepted) (got root path)
octe0 at 192.168.10.97 server 192.168.10.1 server name cinderella.bluezbox.com boot file /src/FreeBSD/tftproot/octeon/boot/kernel/kernel
subnet mask 255.255.255.0 root_server 192.168.10.1 rootfs /src/FreeBSD/tftproot/octeon rootopts nolockd 
Adjusted interface octe0
WARNING: WITNESS option enabled, expect reduced performance.
Trying to mount root from nfs: []...
NFS ROOT: 192.168.10.1:/src/FreeBSD/tftproot/octeon
start_init: trying /sbin/init
octe0: link state changed to UP
Interface octe0 IP-Address 192.168.10.97 Broadcast 192.168.10.255 
Setting hostuuid: 328ec945-1295-11b3-9293-0090fb2626ca.
Setting hostid: 0x131fecc4.
eval: cannot open /etc/fstab: No such file or directory
No suitable dump device was found.
Entropy harvesting: interrupts ethernet point_to_point kickstart.
eval: cannot open /etc/fstab: No such file or directory
eval: cannot open /etc/fstab: No such file or directory
fstab: /etc/fstab:0: No such file or directory
Warning! No /etc/fstab: skipping disk checks.
fstab: /etc/fstab:0: No such file or directory
mount_nfs: can't update /var/db/mounttab for 192.168.10.1:/src/FreeBSD/tftproot/octeon
Mounting local file systems:fstab: /etc/fstab:0: No such file or directory
.
/etc/rc: WARNING: $hostname is not set -- see rc.conf(5).
Starting Network: lo0 octe0 octe1 octe2.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
	options=3<RXCSUM,TXCSUM>
	inet6 ::1 prefixlen 128 
	inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 
	inet 127.0.0.1 netmask 0xff000000 
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
octe0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
	options=b<RXCSUM,TXCSUM,VLAN_MTU>
	ether 00:90:fb:26:26:ca
	inet6 fe80::290:fbff:fe26:26ca%octe0 prefixlen 64 tentative scopeid 0x1 
	inet 192.168.10.97 netmask 0xffffff00 broadcast 192.168.10.255
	nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
	media: Ethernet autoselect (1000baseT <focte1: link state changed to DOWN
ull-duplex>)
	status: active
octe1: flags=8a02<BROADCAST,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
	options=b<RXCSUM,TXCSUM,VLAN_MTU>
	ether 00:90:fb:26:26:cb
	nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
	media: Ethernet autoselect (10baseT/UTP <half-duplex>)
	status: no carrier
octe2: flags=8a02<BROADCAST,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
	options=b<RXCSUM,TXCSUM,VLAN_MTU>
	ether 00:90:fb:26:26:cc
	nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
	media: Ethernet autoselect (<unknown type>)
	status: 
Starting devd.
Starting Network: octe1.
octe1: flags=8a02<BROADCAST,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
	options=b<RXCSUM,TXCSUM,VLAN_MTU>
	ether 00:90:fb:26:26:cb
	nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
	media: Ethernet autoselect (10baseT/UTP <half-duplex>)
	status: no carrier
Starting Network: octe2.
octe2: flags=8a02<BROADCAST,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
	options=b<RXCSUM,TXCSUM,VLAN_MTU>
	ether 00:90:fb:26:26:cc
	nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
	media: Ethernet autoselect (<unknown type>)
	status: 
/etc/rc.d/dhclient: ERROR: 'octe0' is not a DHCP-enabled interface
add net ::ffff:0.0.0.0: gateway ::1
add net ::0.0.0.0: gateway ::1
add net fe80::: gateway ::1
add net ff02::: gateway ::1
fstab: /etc/fstab:0: No such file or directory
fstab: /etc/fstab:0: No such file or directory
fstab: /etc/fstab:0: No such file or directory
fstab: /etc/fstab:0: No such file or directory
fstab: /etc/fstab:0: No such file or directory
Creating and/or trimming log files.
Starting syslogd.
/etc/rc: WARNING: Dump device does not exist.  Savecore not run.
ELF ldconfig path: /lib /usr/lib /usr/lib/compat
ldconfig: /lib: ignoring directory not owned by root
ldconfig: /usr/lib: ignoring directory not owned by root
ldconfig: /usr/lib/compat: ignoring directory not owned by root
Clearing /tmp (X related).
Updating motd:.
fstab: /etc/fstab:0: No such file or directory
can not chdir(/var/spool/clientmqueue/): Permission denied
Nov  8 11:59:39  sm-msp-queue[1104]: NOQUEUE: SYSERR(root): can not chdir(/var/spool/clientmqueue/): Permission denied

Program mode requires special privileges, e.g., root or TrustedUser.
Starting cron.
eval: cannot open /etc/fstab: No such file or directory
Starting background file system checks in 60 seconds.

Sun Nov  8 11:59:41 UTC 1970


FreeBSD/mips (Amnesiac) (ttyu0)



login: 


FreeBSD/mips (Amnesiac) (ttyu0)



login: 


FreeBSD/mips (Amnesiac) (ttyu0)



login: