BootROM - 1.73 Booting from NAND flash General initialization - Version: 1.0.0 AVS selection from EFUSE disabled (Skip reading EFUSE values) mvSysEnvIsFlavourReduced: TWSI Read of 'flavor' failed Detected Device ID 6820 High speed PHY - Version: 2.0 Init RD NAS topology Serdes Lane 3 is USB3 Serdes Lane 4 is SGMII board SerDes lanes topology details: | Lane # | Speed| Type | ------------------------------| | 0 | 6 | SATA0 | | 1 | 5 | PCIe0 | | 2 | 6 | SATA1 | | 3 | 5 | USB3 HOST1 | | 4 | 5 | PCIe1 | | 5 | 0 | SGMII2 | ------------------------------- :** Link is Gen1, check the EP capability PCIe, Idx 0: Link upgraded to Gen2 based on client cpabilities :** Link is Gen1, check the EP capability PCIe, Idx 1: remains Gen1 High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.46.0 mvSysEnvGetTopologyUpdateInfo: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01 (Apr 08 2016 - 15:47:50) Marvell version: 2015_T1.QA.0p16 Boot version : v0.0.4 Board: RD-NAS-88F6820-DDR3 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1866 [MHz] L2 @ 933 [MHz] TClock @ 200 [MHz] DDR3 @ 933 [MHz] DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB NAND: 256 MiB MMC: mv_sdh: 0 DEVINFO offset == 0x7e0000 U-ENV offset == 0x200000 U-ENV offset == 0x200000 S-ENV offset == 0x220000 #### auto_recovery #### [u_env] get auto_recovery == yes [u_env] get auto_recovery == yes [u_env] get boot_part == 2 [u_env] get boot_part_ready == 3 auto_recovery enabled:1, boot_part:2, boot_part_ready:3 S-ENV offset == 0x220000 [boot_count_read] block:0x220000, size:128KB, records:64 [boot_count_read_record] boot_count:2, next_record:61 [boot_count_write] erase:0, auto_recovery->block_offset:0x220000 offset=0x23E800 Updating boot_count ... [boot_count_write] offset:0x23E800 , length:2048 done PCI-e 0 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0 PCI-e 1 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1 USB2.0 0: Host Mode USB3.0 1: Host Mode USB3.0 0: Host Mode Map: Code: 0x1feab000:0x1ff75a20 BSS: 0x1ffef164 Stack: 0x1f9aaf20 Heap: 0x1f9ab000:0x1feab000 U-ENV offset == 0x200000 U-ENV offset == 0x200000 U-Boot Environment: 0x00200000:0x00220000 (NAND) Board configuration detected: mvEthE6171SwitchBasicInit init Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x01 | | egiga1 | SGMII | 0x00 | | egiga2 | SGMII | In-Band | egiga0 [PRIME], egiga1, egiga2 auto_recovery_check changes bootcmd: run altnandboot Hit any key to stop autoboot: 3  0 Marvell>> run       echo $bootcmd dhcp; tftp; go 0x02000000 Marvell>> run bootcmd BOOTP broadcast 1 DHCP client bound to address 192.168.10.105 Using egiga0 device TFTP from server 192.168.10.1; our IP address is 192.168.10.105 Filename 'kernel.armada'. Load address: 0x2000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################### 2 MiB/s done Bytes transferred = 8547940 (826e64 hex) ## Starting application at 0x02000000 ... KDB: debugger backends: ddb KDB: current backend: ddb Copyright (c) 1992-2018 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 12.0-CURRENT #39 r331229M: Mon Mar 19 21:00:31 PDT 2018 gonzo@station.bluezbox.com:/src/FreeBSD/obj/src/FreeBSD/head/arm.armv6/sys/ARMADA38X arm FreeBSD clang version 6.0.0 (tags/RELEASE_600/final 326565) (based on LLVM 6.0.0) WARNING: WITNESS option enabled, expect reduced performance. CPU: ARM Cortex-A9 r4p1 (ECO: 0x00000000) CPU Features: Multiprocessing, Thumb2, Security, VMSAv7, Coherent Walk Optional instructions: UMULL, SMULL, SIMD(ext) LoUU:2 LoC:2 LoUIS:2 Cache level 1: 32KB/32B 4-way data cache WB Read-Alloc Write-Alloc 32KB/32B 4-way instruction cache Read-Alloc real memory = 536866816 (511 MB) avail memory = 511238144 (487 MB) SOC: Marvell 88F6820, TClock 200MHz, Frequency 1866MHz Instruction cache prefetch enabled, data cache prefetch disabled FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs arc4random: no preloaded entropy cache random: entropy device external interface [ath_hal] loaded ofwbus0: simplebus0: on ofwbus0 simplebus1: on simplebus0 l2cache0: mem 0x8000-0x8fff on simplebus1 l2cache0: cannot allocate IRQ, not using interrupt l2cache0: Part number: 0x3, release: 0x9 l2cache0: L2 Cache enabled: 1024KB/32B 16 ways gic0: mem 0xd000-0xdfff,0xc100-0xc1ff on simplebus1 gic0: pn 0x39, arch 0x1, rev 0x2, implementer 0x43b irqs 192 mpic0: mem 0x20a00-0x20ccf,0x21070-0x210c7 irq 17 on simplebus1 mp_tmr0: mem 0xc200-0xc21f irq 3 on simplebus1 Timecounter "MPCore" frequency 933000000 Hz quality 800 mp_tmr1: mem 0xc600-0xc61f irq 4 on simplebus1 Event timer "MPCore" frequency 933000000 Hz quality 1000 twsi0: mem 0x11000-0x1101f irq 5 on simplebus1 iicbus0: on twsi0 iic0: on iicbus0 iicbus0: at addr 0x98 iicbus0: at addr 0xd0 uart0: <16550 or compatible> mem 0x12000-0x120ff irq 7 on simplebus1uart0: console (-1,n,8,1) wdt0: mem 0x20300-0x20333,0x20704-0x20707,0x18260-0x18263 on simplebus1 pmsu0: mem 0x22000-0x22fff on simplebus1 mvneta0: mem 0x70000-0x73fff irq 24 on simplebus1 mvneta0: version is 10 mvneta0: Ethernet address: 60:38:e0:b3:a2:08 mvneta1: mem 0x34000-0x37fff irq 26 on simplebus1 mvneta1: version is 10 mvneta1: Ethernet address: 10:00:66:e3:dd:01 ehci0: mem 0x58000-0x584ff irq 27 on simplebus1 usbus0: EHCI version 1.0 usbus0 on ehci0 rtc0: mem 0xa3800-0xa381f,0x184a0-0x184ab irq 30 on simplebus1 rtc0: registered as a time-of-day clock, resolution 1.000000s ahci0: mem 0xa8000-0xa9fff irq 31 on simplebus1 ahci0: AHCI v1.00 with 2 6Gbps ports, Port Multiplier supported with FBS ahci0: quirks=0x200010<2CH,MRVL_SR_DEL> ahcich0: at channel 0 on ahci0 ahcich1: at channel 1 on ahci0 armada_thermal0: mem 0xe4078-0xe407b,0xe4074-0xe4077 on simplebus1 sdhci_fdt0: mem 0xd8000-0xd8fff,0xdc000-0xdc0ff,0x18454-0x18457 irq 34 on simplebus1 sdhci_fdt0: 1 slot(s) allocated xhci0: mem 0xf8000-0xfbfff,0xfc000-0xfffff irq 36 on simplebus1 xhci0: 32 bytes context size, 32-bit DMA usbus1 on xhci0 pcib_ctrl0: on simplebus0 cpulist0: on ofwbus0 cpu0: on cpulist0 cpu1: on cpulist0 cryptosoft0: Timecounters tick every 1.000 msec mvneta0: link state changed to UP mvneta1: link state changed to UP usbus0: 480Mbps High Speed USB v2.0 usbus1: 5.0Gbps Super Speed USB v3.0 ugen0.1: at usbus0 uhub0: on usbus0 ugen1.1: at usbus1 uhub1: on usbus1 bootpc_init: wired to interface 'mvneta0' Sending DHCP Discover packet from interface mvneta0 (60:38:e0:b3:a2:08) Received DHCP Offer packet on mvneta0 from 192.168.10.1 (accepted) uhub1: 2 ports with 2 removable, self powered mmc0: on sdhci_fdt0 mmc0: No compatible cards found on bus uhub0: 1 port with 1 removable, self powered Sending DHCP Request packet from interface mvneta0 (60:38:e0:b3:a2:08) Received DHCP Ack packet on mvneta0 from 192.168.10.1 (accepted) (got root path) mvneta0 at 192.168.10.105 server 192.168.10.1 boot file kernel.armada subnet mask 255.255.255.0 router 192.168.10.1 root_server 192.168.10.1 rootfs /src/FreeBSD/tftproot/rpi Adjusted interface mvneta0 Release APs WARNING: WITNESS option enabled, expect reduced performance. arc4random: no preloaded entropy cache Trying to mount root from nfs: []... NFS ROOT: 192.168.10.1:/src/FreeBSD/tftproot/rpi Interface mvneta0 IP-Address 192.168.10.105 Broadcast 192.168.10.255 Setting hostuuid: 1a494ea1-1dd2-11b2-ae42-b827eb511ed2. Setting hostid: 0x723a430a. No suitable dump device was found. Starting file system checks: random: unblocking device. mount_nfs: can't update /var/db/mounttab for 192.168.10.1:/src/FreeBSD/tftproot/rpi Mounting local filesystems:. ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/llvm37/lib Setting hostname: armada. Setting up harvesting: [UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,NET_ETHER,NET_TUN,MOUSE,KEYBOARD,ATTACH,CACHED Feeding entropy: . Starting Network: lo0 mvneta0 mvneta1. lo0: flags=8049 metric 0 mtu 16384 options=600003 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3 inet 127.0.0.1 netmask 0xff000000 groups: lo nd6 options=21 mvneta0: flags=8a43 metric 0 mtu 1500 options=bb ether 60:38:e0:b3:a2:08 inet6 fe80::6238:e0ff:feb3:a208%mvneta0 prefixlen 64 tentative scopeid 0x1 inet 192.168.10.105 netmask 0xffffff00 broadcast 192.168.10.255 media: Ethernet 1000baseT status: active nd6 options=29 mvneta1: flags=8a02 metric 0 mtu 1500 options=bb ether 10:00:66:e3:dd:01 media: Ethernet 1000baseT status: active nd6 options=29 Starting devd. Starting Network: mvneta1. mvneta1: flags=8a02 metric 0 mtu 1500 options=bb ether 10:00:66:e3:dd:01 media: Ethernet 1000baseT status: active nd6 options=29 devd: cannot open pid file: Operation not supported add host 127.0.0.1: gateway lo0 fib 0: route already in table add host ::1: gateway lo0 fib 0: route already in table add net fe80::: gateway ::1 add net ff02::: gateway ::1 add net ::ffff:0.0.0.0: gateway ::1 add net ::0.0.0.0: gateway ::1 /etc/rc: WARNING: $mroute6d_enable is not set properly - see rc.conf(5). Mounting NFS filesystems:. ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/llvm37/lib Creating and/or trimming log files. Starting syslogd. syslogd: cannot open pid file: Operation not supported Setting date via ntp. 20 Mar 04:03:41 ntpdate[522]: step time server 50.205.244.28 offset 1521516499.425768 sec NFS access cache time=60 Clearing /tmp (X related). Starting rpcbind. Starting statd. Starting lockd. Updating motd:. Mounting late filesystems:. Performing sanity check on sshd configuration. Starting sshd. Starting sendmail_submit. Starting sendmail_msp_queue. Starting cron. Starting background file system checks in 60 seconds. Tue Mar 20 04:03 FreeBSD/arm (armada) (ttyu0) login: root Mar 20 04:03:48 armada login: ROOT LOGIN (root) ON ttyu0 Last login: Tue Feb 13 22:51:48 on ttyu0 FreeBSD 12.0-CURRENT (ARMADA38X) #39 r331229M: Mon Mar 19 21:00:31 PDT 2018 Welcome to FreeBSD! Release Notes, Errata: https://www.FreeBSD.org/releases/ Security Advisories: https://www.FreeBSD.org/security/ FreeBSD Handbook: https://www.FreeBSD.org/handbook/ FreeBSD FAQ: https://www.FreeBSD.org/faq/ Questions List: https://lists.FreeBSD.org/mailman/listinfo/freebsd-questions/ FreeBSD Forums: https://forums.FreeBSD.org/ Documents installed with the system are in the /usr/local/share/doc/freebsd/ directory, or can be installed later with: pkg install en-freebsd-doc For other languages, replace "en" with a language code like de or fr. Show the version of FreeBSD installed: freebsd-version ; uname -a Please include that output and any error messages when posting questions. Introduction to manual pages: man man FreeBSD directory layout: man hier Edit /etc/motd to change this login announcement. You have new mail. uroot@armada:~ # uname -a FreeBSD armada 12.0-CURRENT FreeBSD 12.0-CURRENT #39 r331229M: Mon Mar 19 21:00:31 PDT 2018 gonzo@station.bluezbox.com:/src/FreeBSD/obj/src/FreeBSD/head/arm.armv6/sys/ARMADA38X arm root@armada:~ #