U-Boot 1.1.4 (Aug 25 2011 - 14:59:09) U-boot DB120 DRAM: sri Wasp 1.2 wasp_ddr_initial_config(255): (32bit) ddr2 init 128 MB Top of RAM usable for U-Boot at: 88000000 Reserving 249k for U-Boot at: 87fc0000 Reserving 192k for malloc() at: 87f90000 Reserving 44 Bytes for Board Info at: 87f8ffd4 Reserving 36 Bytes for Global Data at: 87f8ffb0 Reserving 128k for boot params() at: 87f6ffb0 Stack Pointer at: 87f6ff98 Now running in RAM - U-Boot at: 87fc0000 id read 0x100000ff flash size 8MB, sector count = 128 Flash: 8 MB pci_init_board: PCIe PLL not set for 40MHz refclk *** Warning *** : PCIe WLAN Module not found !!! In: serial Out: serial Err: serial Net: ag934x_enet_initialize... Fetching MAC Address from 0x87feaf58 wasp reset mask:c03300 WASP ----> S17 PHY * : cfg1 0x7 cfg2 0x7114 eth0: 00:03:7f:11:23:55 athrs17_reg_init: complete eth0 up eth0 Hit any key to stop autoboot: 0 ar7240> tftpboot 0x80050000 kernel.DB120; go 0x80050100 Trying eth0 dup 1 speed 1000 Using eth0 device TFTP from server 192.168.169.1; our IP address is 192.168.169.2 Filename 'kernel.DB120'. Load address: 0x80050000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############## done Bytes transferred = 5724399 (5758ef hex) ## Starting application at 0x80050100 ... CPU platform: Atheros AR9344 rev 2 CPU Frequency=560 MHz CPU DDR Frequency=480 MHz CPU AHB Frequency=240 MHz platform frequency: 560 MHz CPU reference clock: 40 MHz CPU MDIO clock: 100 MHz arguments: a0 = 00000001 a1 = 87fa04c4 a2 = 00000010 a3 = ffffffff Cmd line:argv is invalid Environment: envp is invalid Cache info: picache_stride = 4096 picache_loopcount = 16 pdcache_stride = 4096 pdcache_loopcount = 8 cpu0: MIPS Technologies processor v76.151 MMU: Standard TLB, 32 entries L1 i-cache: 4 ways of 512 sets, 32 bytes per line L1 d-cache: 4 ways of 256 sets, 32 bytes per line Config1=0xbee3519e Config3=0x2c20 ar934x_chip_init_gmac: DB120 MAC bringup hack to peel off arge0.. ar934x_configure_gmac: ETH_CFG=0x00000001 KDB: debugger backends: ddb KDB: current backend: ddb Copyright (c) 1992-2013 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 11.0-CURRENT #177 r256379M: Sat Oct 12 06:08:20 PDT 2013 adrian@lucy:/usr/home/adrian/work/freebsd/svn/head/obj/mipseb/mips.mips/usr/home/adrian/work/freebsd/svn/head/src/sys/DB120 mips gcc version 4.2.1 20070831 patched [FreeBSD] WARNING: WITNESS option enabled, expect reduced performance. real memory = 134217728 (131072K bytes) avail memory = 123678720 (117MB) random device not loaded; using insecure entropy random: initialized nexus0: clock0: on nexus0 Timecounter "MIPS32" frequency 280000000 Hz quality 800 Event timer "MIPS32" frequency 280000000 Hz quality 800 device_attach(): feeding 4 bit(s) of entropy from clock0 argemdio0: at mem 0x19000000-0x19000fff on nexus0 mdio0: on argemdio0 mdioproxy0: on mdio0 device_attach(): feeding 4 bit(s) of entropy from mdioproxy0 device_attach(): feeding 4 bit(s) of entropy from mdio0 device_attach(): feeding 4 bit(s) of entropy from argemdio0 argemdio1: at mem 0x1a000000-0x1a000fff on nexus0 mdio1: on argemdio1 mdioproxy1: on mdio1 device_attach(): feeding 4 bit(s) of entropy from mdioproxy1 arswitch1: chipname=AR9340, id=00000000 arswitch1: chipname=AR9340, id=00000000 arswitch1: on mdio1 arswitch_attach: PHY0: ID1=004d, ID2=d042 arswitch_attach: PHY1: ID1=004d, ID2=d042 arswitch_attach: PHY2: ID1=004d, ID2=d042 arswitch_attach: PHY3: ID1=004d, ID2=d042 arswitch_attach: PHY4: ID1=004d, ID2=d042 arswitch1: arswitch_readphy: (5.02): failed to read arswitch1: arswitch_readphy: (5.03): failed to read arswitch_attach: PHY5: ID1=ffffffff, ID2=ffffffff arswitch1: ar9340_hw_global_setup: GMII arswitch1: ar9340_hw_global_setup: PHY4 - Local miibus0: on arswitch1 ukphy0: PHY 0 on miibus0 ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto device_attach(): feeding 4 bit(s) of entropy from ukphy0 device_attach(): feeding 4 bit(s) of entropy from miibus0 arswitch1: miibus0 attached to pseudo interface arswitch1port1 miibus1: on arswitch1 ukphy1: PHY 1 on miibus1 ukphy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto device_attach(): feeding 4 bit(s) of entropy from ukphy1 device_attach(): feeding 4 bit(s) of entropy from miibus1 arswitch1: miibus1 attached to pseudo interface arswitch1port2 miibus2: on arswitch1 ukphy2: PHY 2 on miibus2 ukphy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto device_attach(): feeding 4 bit(s) of entropy from ukphy2 device_attach(): feeding 4 bit(s) of entropy from miibus2 arswitch1: miibus2 attached to pseudo interface arswitch1port3 miibus3: on arswitch1 ukphy3: PHY 3 on miibus3 ukphy3: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto device_attach(): feeding 4 bit(s) of entropy from ukphy3 device_attach(): feeding 4 bit(s) of entropy from miibus3 arswitch1: miibus3 attached to pseudo interface arswitch1port4 etherswitch0: on arswitch1 device_attach(): feeding 4 bit(s) of entropy from etherswitch0 mdio2: on arswitch1 mdioproxy2: on mdio2 device_attach(): feeding 4 bit(s) of entropy from mdioproxy2 device_attach(): feeding 4 bit(s) of entropy from mdio2 arswitch1: arswitch_statchg arswitch1: arswitch_statchg arswitch1: arswitch_statchg arswitch1: arswitch_statchg device_attach(): feeding 4 bit(s) of entropy from arswitch1 device_attach(): feeding 4 bit(s) of entropy from mdio1 device_attach(): feeding 4 bit(s) of entropy from argemdio1 apb0 at irq 4 on nexus0 uart0: <16550 or compatible> on apb0 uart0: console (115200,n,8,1) device_attach(): feeding 4 bit(s) of entropy from uart0 gpio0: on apb0 gpio0: [GIANT-LOCKED] gpio0: gpio pinmask=0x0 gpioc0: on gpio0 device_attach(): feeding 4 bit(s) of entropy from gpioc0 gpiobus0: on gpio0 device_attach(): feeding 4 bit(s) of entropy from gpiobus0 device_attach(): feeding 4 bit(s) of entropy from gpio0 device_attach(): feeding 4 bit(s) of entropy from apb0 ehci0: at mem 0x1b000100-0x1b0010ff irq 1 on nexus0 usbus0: set host controller mode usbus0: EHCI version 1.0 usbus0: set host controller mode usbus0 on ehci0 device_attach(): feeding 4 bit(s) of entropy from usbus0 device_attach(): feeding 4 bit(s) of entropy from ehci0 arge0: at mem 0x19000000-0x19000fff irq 2 on nexus0 arge0: arge_fetch_pll_config: pll_1000 = 0x6000000 arge0: arge_attach: overriding MII mode to 'RGMII' arge0: finishing attachment, phymask 0000, proxy null arge0: Ethernet address: 62:73:64:0f:08:93 device_attach(): feeding 4 bit(s) of entropy from arge0 arge1: at mem 0x1a000000-0x1a000fff irq 3 on nexus0 arge1: arge_attach: overriding MII mode to 'GMII' arge1: finishing attachment, phymask 0000, proxy null arge1: Ethernet address: 62:73:64:22:21:4c device_attach(): feeding 4 bit(s) of entropy from arge1 ath0: Vendor=0x168c, Device=0x0031 ath0: Vendor=0x168c, Device=0x0031 ath0: at mem 0x18100000-0x1811ffff irq 0 on nexus0 ath0: eeprom @ 0x1fff0000 (16384 bytes) ath0: eeprom data @ 0xbfff0000 ar9300_set_stub_functions: setting stub functions ar9300_set_stub_functions: setting stub functions Bootstrap clock 40MHz Enterprise mode: 0x00000000 ar9300_attach: calling ar9300_hw_attach ar9300_hw_attach: calling ar9300_eeprom_attach ar9300_flash_map: unimplemented for now Restoring Cal data from DRAM ar9300_hw_attach: ar9300_eeprom_attach returned 0 ath0: RX status length: 48 ath0: RX buffer size: 4096 ath0: TX descriptor length: 128 ath0: TX status length: 36 ath0: TX buffers per descriptor: 4 ar9300_freebsd_setup_x_tx_desc: called, 0x0/0, 0x0/0, 0x0/0 ath0: ath_edma_setup_rxfifo: type=0, FIFO depth = 16 entries ath0: ath_edma_setup_rxfifo: type=1, FIFO depth = 128 entries ath0: [HT] enabling HT modes ath0: [HT] enabling short-GI in 20MHz mode ath0: [HT] 1 stream STBC receive enabled ath0: [HT] 1 stream STBC transmit enabled ath0: [HT] 2 RX streams; 2 TX streams ath0: AR9340 mac 768.2 RF5110 phy 2912.5 ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0000 device_attach(): feeding 4 bit(s) of entropy from ath0 spi0: at mem 0x1f000000-0x1f00000f on nexus0 spibus0: on spi0 mx25l0: at cs 0 on spibus0 mx25l0: s25fl064, sector 65536 bytes, 128 sectors device_attach(): feeding 4 bit(s) of entropy from mx25l0 device_attach(): feeding 4 bit(s) of entropy from spibus0 device_attach(): feeding 4 bit(s) of entropy from spi0 ar71xx_wdog0: on nexus0 device_attach(): feeding 4 bit(s) of entropy from ar71xx_wdog0 device_attach(): feeding 4 bit(s) of entropy from nexus0 Timecounters tick every 1.000 msec arswitch1port1: link state changed to DOWN arswitch1port2: link state changed to DOWN arswitch1port3: link state changed to DOWN arswitch1port4: link state changed to DOWN usbus0: 480Mbps High Speed USB v2.0 ugen0.1: at usbus0 uhub0: on usbus0 map/rootfs.uncompress: GEOM_ULZMA image found map/rootfs.uncompress: 295 x 65536 blocks random_yarrow_reseed(): fast: 0 68 0 0 0 0 0 0 6 0 0 0 0 0 0 0 0 random_yarrow_reseed(): slow: 0 68 0 0 0 0 0 0 5 0 0 0 0 0 0 0 0 random: unblocking device. WARNING: WITNESS option enabled, expect reduced performance. uhub0: 1 port with 1 removable, self powered device_attach(): feeding 4 bit(s) of entropy from uhub0 Trying to mount root from ufs:map/rootfs.uncompress []... warning: no time-of-day clock registered, system time will not be set accurately Oct 6 17:03:30 init: login_getclass: unknown class 'daemon' *** Populating /var .. *** Loading configuration files .. *** Restoring from /dev/map/cfg .. dd: /dev/map/cfg: No such file or directory gunzip: (stdin): unexpected end of file 0 blocks *** Completed. *** setting up hostname *** Load kernel modules kldload: can't load bridgestp: File exists kldload: can't load if_bridge: No such file or directory kldload: can't load random: File exists *** Unblocking /dev/random.. *** bringing up loopback .. *** Starting networking via /etc/rc.d/base/net dev.ath.0.txq_mcastq_maxdepth: 512 -> 32 sysctl: unknown oid 'dev.ath.1.txq_mcastq_maxdepth': No such file or directory *** Interface: arge0: start *** Interface: arge0: done *** Interface: bridge0: start bridge0: Ethernet address: 2e:c5:64:4d:a0:85 arge0: promiscuous mode enabled bridge0: link state changed to UP *** Interface: bridge0: done *** Default password/login databases .. *** inetd *** Done! FreeBSD/mips (freebsd-wifi-build) (ttyu0) login: